Difference between revisions of "PDX2000 Firmware Upgrade"
From skratchtek
(2 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | The PDX2000 and PDX3000 turntables are very similar in terms of circuitry - really the only difference is in the main MCU. | ||
+ | |||
[https://www.youtube.com/watch?v=JjtfPExJrIE The main guide is in this video.] | [https://www.youtube.com/watch?v=JjtfPExJrIE The main guide is in this video.] | ||
− | * Modify the main circuit board : | + | * '''Modify the main circuit board''' : |
** Replace the MCU (QU01) with a HD64F3052F25 (available used from utsource) | ** Replace the MCU (QU01) with a HD64F3052F25 (available used from utsource) | ||
** Replace the Crystal (XU01) with a 25MHz one | ** Replace the Crystal (XU01) with a 25MHz one | ||
Line 7: | Line 9: | ||
*** [[File:Cuttrace.png|200px]] | *** [[File:Cuttrace.png|200px]] | ||
− | * Build a programming cable using an 8-pin JST PH connector and some dupont wires, this is the wiring for it : | + | * '''Build a programming cable''' using an 8-pin JST PH connector and some dupont wires, this is the wiring for it : |
** [[File:Wiring2.png|200px]] | ** [[File:Wiring2.png|200px]] | ||
− | * Connect a USB-TTL serial adapter to your PC, and connect it to JU05 (FLASH) on the Vestax PCB using the cable you just made | + | * '''Connect a USB-TTL serial adapter to your PC''', and connect it to JU05 (FLASH) on the Vestax PCB using the cable you just made |
− | * [https://www.renesas.com/us/en/software-tool/flash-development-toolkit-programming-gui#download Install the renesas flash tools] - you want the "[Evaluation Software] Flash Development Toolkit V.4.09 Release 03" | + | * '''[https://www.renesas.com/us/en/software-tool/flash-development-toolkit-programming-gui#download Install the renesas flash tools]''' - you want the "[Evaluation Software] Flash Development Toolkit V.4.09 Release 03" |
* Run '''Flash Development Toolkit 4.09 Basic'''. | * Run '''Flash Development Toolkit 4.09 Basic'''. |
Revision as of 07:15, 20 September 2021
The PDX2000 and PDX3000 turntables are very similar in terms of circuitry - really the only difference is in the main MCU.
The main guide is in this video.
- Modify the main circuit board :
- Build a programming cable using an 8-pin JST PH connector and some dupont wires, this is the wiring for it :
- Connect a USB-TTL serial adapter to your PC, and connect it to JU05 (FLASH) on the Vestax PCB using the cable you just made
- Install the renesas flash tools - you want the "[Evaluation Software] Flash Development Toolkit V.4.09 Release 03"
- Run Flash Development Toolkit 4.09 Basic.
- Go to "Options->New Settings" (it might automatically do this the first time you start it)
- Type "H8/3052" in the filter box and select the first option in the list, click next
- Select the COM port of your USB serial adapter (you can find this in Device Manager), click next
- Set the CPU crystal frequency to 25MHz, click next
- Make sure BOOT Mode and Use Default is selected, click next
- Click Finish
- Download the modified PDX3000 firmware, and load it into the "User/Data Area" box of the Flash Development Toolkit
- Click "Program Flash", it will take 10 seconds or so.
- If all is ok, it will say "Image written to device" in green - if not, check your connections and soldering