Difference between revisions of "Nanofader Fader Guide"
(→Pro-X-Fade) |
|||
| (2 intermediate revisions by one other user not shown) | |||
| Line 3: | Line 3: | ||
==Carbon-track faders== | ==Carbon-track faders== | ||
| − | If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper | + | If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper. |
The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin. | The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin. | ||
| + | |||
| + | So for dual-sided cut, connect "TERMINAL1" and "TERMINAL2" to the "G" pin of the nanofader "FADER" connector, and connect "WIPER" to the "W" pin. | ||
===Vestax PCV=== | ===Vestax PCV=== | ||
| Line 14: | Line 16: | ||
You can use either CH1 or CH2. | You can use either CH1 or CH2. | ||
| − | |||
| − | |||
===Pro-X-Fade=== | ===Pro-X-Fade=== | ||
| − | + | The pinout of the Pro-X-Fade is as follows : | |
| + | |||
| + | [[File:Proxfadepinout.png|400px]] | ||
| + | |||
| + | You can use either CH1 or CH2. | ||
==Innofader== | ==Innofader== | ||
| Line 43: | Line 47: | ||
===Mini Innofader PNP P=== | ===Mini Innofader PNP P=== | ||
| − | Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable", which | + | Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable" or "3-pin small cable", which have the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual. |
===Innofader PNP=== | ===Innofader PNP=== | ||
Probably the best way to wire up the '''Innofader PNP''' is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual. | Probably the best way to wire up the '''Innofader PNP''' is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual. | ||
Latest revision as of 14:11, 6 March 2016
This is a quick guide to connecting a fader to the nanofader circuit.
Contents
Carbon-track faders
If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper.
The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin.
So for dual-sided cut, connect "TERMINAL1" and "TERMINAL2" to the "G" pin of the nanofader "FADER" connector, and connect "WIPER" to the "W" pin.
Vestax PCV
The pinout of the vestax PCV is as follows :
You can use either CH1 or CH2.
Pro-X-Fade
The pinout of the Pro-X-Fade is as follows :
You can use either CH1 or CH2.
Innofader
All Innofader varieties work reasonably well, but they require power so three wires will be required.
OEM Mini Innofader
The cheapest Innofader is the model sold directly to equipment manufacturers, and can be obtainable as a spare part or upgrade for various mixers (e.g. various reloop mixers, DJTech DIF-1S, Native Instruments Z2). The pinout of the OEM Mini Innofader is :
The wiring is as follows :
GND - Wire to "G" (ground) pin on nanofader "FADER" connector
VCA2 - Do not connect
VCA1 - Wire to "W" (wiper) pin on nanofader "FADER" connector
V+ - Wire to "+" (supply) pin on nanofader "FADER" connector
Mini Innofader PNP P
Probably the best way to wire up the Mini Innofader PNP P is to extend the supplied "3-pin large cable" or "3-pin small cable", which have the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual.
Innofader PNP
Probably the best way to wire up the Innofader PNP is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual.
