Nanofader Fader Guide - Revision history

90.217.82.161: /* Pro-X-Fade */

2016-03-06T19:11:01Z

‎Pro-X-Fade

Rasteri at 15:08, 5 March 2016

2016-03-05T15:08:03Z

Rasteri: /* Mini Innofader PNP P */

2016-03-04T23:25:22Z

‎Mini Innofader PNP P

Rasteri at 22:00, 4 March 2016

2016-03-04T22:00:22Z

Rasteri: Created page with "This is a quick guide to connecting a fader to the nanofader circuit. ===Carbon-track faders=== If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade..."

2016-03-04T21:59:07Z

Created page with "This is a quick guide to connecting a fader to the nanofader circuit. ===Carbon-track faders=== If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade..."

New page

This is a quick guide to connecting a fader to the nanofader circuit.

===Carbon-track faders===

If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper. If you want dual-sided cut, connect BOTH terminals together.

The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin.

====Vestax PCV====

The pinout of the vestax PCV is as follows :

[[File:Pt01mod-pcv_pinout.jpg|400px]]

You can use either CH1 or CH2.

So for example, connect "CH1 TERMINAL1" and "CH1 TERMINAL2" to the "G" pin of the nanofader "FADER" connector, and connect "CH1 WIPER" to the "W" pin.

====Pro-X-Fade====

(TODO : write this section)

===Innofader===

All Innofader varieties work reasonably well, but they require power so three wires will be required.

====OEM Mini Innofader====

The cheapest Innofader is the model sold directly to equipment manufacturers, and can be obtainable as a spare part or upgrade for various mixers (e.g. various reloop mixers, DJTech DIF-1S, Native Instruments Z2). The pinout of the OEM Mini Innofader is :

[[File:Miniinnopinout.png]]

The wiring is as follows :

'''GND''' - Wire to "G" (ground) pin on nanofader "FADER" connector

'''VCA2''' - Do not connect

'''VCA1''' - Wire to "W" (wiper) pin on nanofader "FADER" connector

'''V+''' - Wire to "+" (supply) pin on nanofader "FADER" connector

====Mini Innofader PNP P====

Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual.

====Innofader PNP====

Probably the best way to wire up the '''Innofader PNP''' is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual.

@@ Line 19: / Line 19: @@
 ===Pro-X-Fade===
-The pinout of the vestax PCV is as follows :
+The pinout of the Pro-X-Fade is as follows :
 [[File:Proxfadepinout.png|400px]]
 You can use either CH1 or CH2.
 ==Innofader==

@@ Line 3: / Line 3: @@
 ==Carbon-track faders==
-If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper. If you want dual-sided cut, connect BOTH terminals together.
+If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper.
 The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin.
 ===Vestax PCV===
@@ Line 14: / Line 16: @@
 You can use either CH1 or CH2.
 ===Pro-X-Fade===
-(TODO : write this section)
+The pinout of the vestax PCV is as follows :
 ==Innofader==

@@ Line 43: / Line 43: @@
 ===Mini Innofader PNP P===
-Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual.
+Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable" or "3-pin small cable", which have the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual.
 ===Innofader PNP===
 Probably the best way to wire up the '''Innofader PNP''' is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual.

@@ Line 1: / Line 1: @@
 This is a quick guide to connecting a fader to the nanofader circuit.
-===Carbon-track faders===
+==Carbon-track faders==
 If you have a carbon-track based fader (Vestax PCV, Penny & Giles, Pro-X-Fade), you only need two wires - one for the terminal(s), one for the wiper. If you want dual-sided cut, connect BOTH terminals together.
@@ Line 7: / Line 7: @@
 The terminal(s) connect to the ground or "G" pin of the nanofader "FADER" connector, and the wiper connects to the "W" pin.
-====Vestax PCV====
+===Vestax PCV===
 The pinout of the vestax PCV is as follows :
@@ Line 17: / Line 17: @@
 So for example, connect "CH1 TERMINAL1" and "CH1 TERMINAL2" to the "G" pin of the nanofader "FADER" connector, and connect "CH1 WIPER" to the "W" pin.
-====Pro-X-Fade====
+===Pro-X-Fade===
 (TODO : write this section)
-===Innofader===
+==Innofader==
 All Innofader varieties work reasonably well, but they require power so three wires will be required.
-====OEM Mini Innofader====
+===OEM Mini Innofader===
 The cheapest Innofader is the model sold directly to equipment manufacturers, and can be obtainable as a spare part or upgrade for various mixers (e.g. various reloop mixers, DJTech DIF-1S, Native Instruments Z2). The pinout of the OEM Mini Innofader is :
@@ Line 41: / Line 41: @@
 '''V+''' - Wire to "+" (supply) pin on nanofader "FADER" connector
-====Mini Innofader PNP P====
+===Mini Innofader PNP P===
 Probably the best way to wire up the '''Mini Innofader PNP P''' is to extend the supplied "3-pin large cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Mini Innofader manual.
-====Innofader PNP====
+===Innofader PNP===
 Probably the best way to wire up the '''Innofader PNP''' is to extend the supplied "3-pin small cable", which has the same pinout as the nanofader "FADER" connector. Just remember to do a polarity check first, as described in the Innofader PNP manual.